DIY Mirror Body Concepts: Find out how to Body a Mirror in 8 Steps

29

After taking all of those measurements, you’ll have the ability to decide the dimensions of the body and whether or not it is going to be hooked up to the wall or the mirror itself.

3. Lower the baseboards

Use a miter noticed set at a 45-degree angle to chop your boards to the suitable size. If you happen to don’t have a miter noticed, many house enchancment shops, like House Depot or Lowe’s, both promote pre-mitered trim or have gear you should utilize within the retailer.

Whenever you’re completed, you’ll wish to hold the 4 items of the MDF board aside, as you’ll finally set up them individually. It could assist to put them out flat simply to ensure every little thing will line up appropriately when you do dangle up the mirror body.

Alternatively, you may also use non-mitered boards with ornamental nook block moldings. Be aware: If you’re attaching the DIY body to the wall, you will want to chop a notch (for the mirror) into the wooden so your entire body will sit flush with the wall.

4. Paint the baseboards

After you’ve minimize the baseboards to dimension, the true enjoyable begins. It’s time to color them. If you happen to’re framing a toilet mirror, it might make sense to coordinate the colour along with your vainness, nevertheless it’s actually as much as you. When you’ve chosen your chosen hue, paint the boards on all sides utilizing a curler, brush, or spray gun. Keep in mind, no water-based paint!

Don’t overlook to color the again, as a result of it should mirror within the mirror. In case your boards may gain advantage from a second layer, be at liberty so as to add that too. Let the paint dry for no less than two hours.

5. Sand the baseboards

Calmly sand the baseboards with an additional superb sanding pad after which gently wipe them clear with a tack material.

You might wish to apply a topcoat or sealer at this level, particularly in case your DIY is for a loo mirror the place you can splash water on it. A polyurethane coat may fit effectively, and also you’ll have the ability to select the sheen you want, whether or not ​​matte, satin, semi-gross, or high-gloss.

Just like the paint, ensure you’re utilizing an oil-based product. This sort of polyurethane can take longer to dry, so let your mirror body sit for 4 to eight hours.

6. Set up the mirror body

As soon as the paint is dry, it’s time to put in the mirror body. Beginning with the underside piece, apply liquid nails to the again of the board, avoiding the sting closest to the mirror. Press onto the mirror or wall, and use a degree to ensure the body is straight. Safe with painter’s tape to maintain every little thing in place whereas the development adhesive dries.
buy amoxicillin generic https://buywithoutprescriptiononlinerx.com/amoxicillin.html over the counter

Repeat the method, including the 2 aspect items subsequent and ending with the highest piece. Wipe off any extra glue alongside the wall or mirror.

7. Contact up the body

After the mirror body has dried fully—for about 24 hours—take away the painter’s tape and repair any uneven corners with caulk. Utilizing a caulk gun, run a bead of silicone caulk alongside any gaps or joints and easy with a moist finger. As soon as this has dried, contact up with paint.
buy amitriptyline generic https://buywithoutprescriptiononlinerx.com/amitriptyline.html over the counter

8. Get inventive and customise your mirror body

Utilizing an MDF baseboard is actually the best solution to body wall mirrors, however you may also use completely different supplies to make a one-of-a-kind piece. There are many DIY mirror body concepts on the market. If you happen to just like the look of wood frames, strive reclaimed wooden boards for a country look or a brilliant paint coloration to coordinate with the wall coloration or wallpaper. You would even paint a selected design, add a textural component, or take into consideration including a string of lights to additional make over your house. Your creativity is the restrict with a activity like this, and isn’t that the entire level of a DIY challenge in any case?

Comments are closed.